I wish I had the patience to do something such as this. But I don’t so I
will send my money to you.
Zyriik Vacirca April 1, 2012 @
4:55 am
I like how during this whole process of the board slipping off n bouncing
around, there is not a single expletive spouted in frustration.
MXMSKustomShop July 17, 2012 @
1:19 am
Thanks that means a lot
marshhhhhhhh August 11, 2012 @
8:50 pm
i Have a Question Please Reply.!!! After i Tape it.. like.. Once i paint
the Flames.. how would i paint the Rest of the Gas tank ??? what would i
use?? to make sure i don’t paint the flames ..
Airbrushing Tips August 21, 2012 @
1:15 am
@marshhhhhhhh Paint your base color first, then lay out your graphics.
MXMSKustomShop September 5, 2012 @
4:25 am
Actually paint your base and clear let dry for 24 hrs come back and wet
sand with 800grit to scuff the paint completely dull be careful not to sand
into the base though and then lay out your flames or graphics clear ones
again then wet sand with 1500 or finer and buff to a shine but this is the
most important step after you get done doing all of that… Sit the piece
down crack open a cold one and enjoy a job well done =)
mko2212 March 17, 2013 @
3:04 pm
Hey there, i would like to know how you get sharp line when the tape gets
off. My line krak a little and, some say its becouce i youse waterbased
paint??? Or is it becouce i youse 2000 sandpaper??
MXMSKustomShop March 20, 2013 @
3:29 am
im sorry but i dont know what you’re trying to say!
Peaceful Violence April 14, 2013 @
12:20 am
hey good video, had to skip a head at times but good info.
bradley taylor July 5, 2013 @
4:45 am
Get to the point!
MXMSKustomShop July 10, 2013 @
12:37 am
no one is forcing you to watch the video!
tony taglienti July 30, 2013 @
6:08 am
carpinuk August 12, 2013 @
2:44 pm
hi, i’m thinking about doing a paint job on my bike and this video was
really helpful, i’m still thinking about what design i will use but if i
want to carry the pattern from the fairing up to the tank do you have any
tips to make sure the designs line up, at the moment the only way i can
think of is to fit them to the bike, mark it out then take the panels back
off for spraying?
PinoyKlasika October 22, 2013 @
2:04 pm
@MXMSKustomShop where can I get those white large width Tape that doesnt
mess up the paint when I put it cause I trying to paint my bicycle Fender
and what are those tape called
December 11, 2011 @ 1:01 pm
I wish I had the patience to do something such as this. But I don’t so I
will send my money to you.
April 1, 2012 @ 4:55 am
I like how during this whole process of the board slipping off n bouncing
around, there is not a single expletive spouted in frustration.
July 17, 2012 @ 1:19 am
Thanks that means a lot
August 11, 2012 @ 8:50 pm
i Have a Question Please Reply.!!! After i Tape it.. like.. Once i paint
the Flames.. how would i paint the Rest of the Gas tank ??? what would i
use?? to make sure i don’t paint the flames ..
August 21, 2012 @ 1:15 am
@marshhhhhhhh Paint your base color first, then lay out your graphics.
September 5, 2012 @ 4:25 am
Actually paint your base and clear let dry for 24 hrs come back and wet
sand with 800grit to scuff the paint completely dull be careful not to sand
into the base though and then lay out your flames or graphics clear ones
again then wet sand with 1500 or finer and buff to a shine but this is the
most important step after you get done doing all of that… Sit the piece
down crack open a cold one and enjoy a job well done =)
March 17, 2013 @ 3:04 pm
Hey there, i would like to know how you get sharp line when the tape gets
off. My line krak a little and, some say its becouce i youse waterbased
paint??? Or is it becouce i youse 2000 sandpaper??
March 20, 2013 @ 3:29 am
im sorry but i dont know what you’re trying to say!
April 14, 2013 @ 12:20 am
hey good video, had to skip a head at times but good info.
July 5, 2013 @ 4:45 am
Get to the point!
July 10, 2013 @ 12:37 am
no one is forcing you to watch the video!
July 30, 2013 @ 6:08 am
August 12, 2013 @ 2:44 pm
hi, i’m thinking about doing a paint job on my bike and this video was
really helpful, i’m still thinking about what design i will use but if i
want to carry the pattern from the fairing up to the tank do you have any
tips to make sure the designs line up, at the moment the only way i can
think of is to fit them to the bike, mark it out then take the panels back
off for spraying?
October 22, 2013 @ 2:04 pm
@MXMSKustomShop where can I get those white large width Tape that doesnt
mess up the paint when I put it cause I trying to paint my bicycle Fender
and what are those tape called
October 4, 2014 @ 4:38 pm
What’s the name of that tape?